Relay board for WLED controller (12V)
Product number:
HW10011
Product information "Relay board for WLED controller (12V)"
(Shipping only to: DE, PL)
Description:
This product is designed for use in conjunction with WLED controllers V43 / V63 / V70. It allows the 12V LED strips to be switched off in the “off” state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled.
Usage information: HERE
Scope of delivery:
- Relay board
Accessories:
- Suitable housing is available separately
Technical data:
- Supply voltage: 12 V +/- 0.5 V
- Ambient temperature operation: +5 °C … +35 °C
- Ambient temperature storage/transport: -20 °C … 60 °C
- Dimensions: 78x47x20 mm
- Weight: 45 g
- Maximum permanent current carrying capacity per power path (+12 V, GND): up to 9 A (depending on cable cross section and environment)
- Screw terminals: Target torque: 0.4 Nm
- Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve
- Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm
- Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path:
- 0.5 mm2 / 3 A (36 W)
- 0.75 mm2 / NO: 6 A (72 W), NC: 5 A (60 W)
- 1 mm2 - 2.5 mm2 / NO: 9 A (108 W), NC: 5 A (60 W)
*This information alone may not be used to dimension the cables. This requires other conditions, such as cable type, installation type, cable routing, cable length etc. are taken into account.
Mandatory information:
- WEEE Reg. No.: DE34359026
- Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München
Warnings:
- This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system.
- This product may only be operated with safety extra-low voltage (SELF) (protection class III).
- Maximum permissible nominal value of the fuse is 10 A!
- This product is not a toy! It must be kept out of the reach of children and must not be used as a toy.
- When connecting to the device terminals, please note the permitted cables and cross sections.
- Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be avoided by carefully designing the light chain or lighting system and, if necessary, integrating the safety elements both in normal operation and in the event of a fault.
- Install and connect this product only when there is no voltage! Make sure the polarity is correct!
- We assume no liability for property damage or personal injury caused by improper use or failure to observe the hazard warnings. In these cases, the warranty claim also expires! We assume no liability for consequential damage.
- Keep the usage information digitally or printed so that you can always access it.
- This product is only suitable for use in devices for apartment-like surroundings.
- Protect this product from electrostatic discharge to avoid damage.
- Any use other than that described in this usage information is not intended and leads to exclusion of warranty and liability.
Recommended
Enclosure for WLED boards
€4.99*
Description:
Plastic housing suitable for WLED boards:
WLED V31 Board;
WLED V41 Board;
WLED V43 Board (5-24V);
WLED V63 5V/12V shield with ESP8266 or ESP32;
Relay board (5V, 12V or 24V);
Fuse board
Scope of delivery:
Top part
Bottom part
4 screws
Mandatory information:Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München, Germany
Warnings:
This product is not a toy! It must be kept out of the reach of children and must not be used as a toy.
This product is only suitable for use in residential-like environments. Protect this product from direct sunlight.
When used with the WLED Controller V43 together with the Ethernet adapter, an extra cutout must be made in the housing by the customer. Please see the product images for the Ethernet adapter.
miniOTO fuses
From
€0.29*
Nominal values:
5 A (beige)
Description:
High-quality fuses from a European manufacturer iMaXX from Netherlands.
Type: miniOTO, F70xx Series.
Suitable for our WLED controllers, relay boards and fuse boards.
Available ratings: 4 A, 5 A, 7.5 A, 10 A, 15 A.
Complies with international specifications, compliant with DIN ISO 8820-3, JASO D612, SAE J2077 and other standards.Manufacturer:
iMAXX Companies, Ohmweg 61, 2952 BB Alblasserdam, Holland
Technical data:
max. Voltage: 32V
Breaking capacity: 1 kA
Width: 11.1 mm
Packaging weight: 0.001 kg
RoHS compliant: Yes
miniOTO fuses
From
€0.29*
Nominal values:
7.5 A (brown)
Description:
High-quality fuses from a European manufacturer iMaXX from Netherlands.
Type: miniOTO, F70xx Series.
Suitable for our WLED controllers, relay boards and fuse boards.
Available ratings: 4 A, 5 A, 7.5 A, 10 A, 15 A.
Complies with international specifications, compliant with DIN ISO 8820-3, JASO D612, SAE J2077 and other standards.Manufacturer:
iMAXX Companies, Ohmweg 61, 2952 BB Alblasserdam, Holland
Technical data:
max. Voltage: 32V
Breaking capacity: 1 kA
Width: 11.1 mm
Packaging weight: 0.001 kg
RoHS compliant: Yes