ABC! WLED Controller V31/ESP8266

Description: Based on CH340G chip; Includes automatic reset (RST/IO0) control; Compatible with Arduino, PlatformIO, web based installers (https://wled-install.github.io/, https://install.wled.me/); Micro-USB socket; Pin compatible with WLED  V41 / V43 / V70 / V73 boards, just plug in and program; Scope of delivery: USB adapter (without cable) Mandatory information: WEEE Reg. No.: DE34359026 Special information: This product is not a toy! It must be kept out of the reach of children and must not be used as a toy.

(Shipping only to: DE, PL) Description This product is designed for use in conjunction with WLED Controller V43. It allows the 24V LED strips to be switched off in the “off” state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled. Usage information: HERE Scope of delivery: Relay board Accessories: Suitable housing is available separately Technical data Supply voltage: 24 V +/- 0.5 V Ambient temperature operation: +5°C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight: 45 g Maximum permanent current carrying capacity per power path (+24V, GND): up to 9 A (depending on cable cross section and environment) Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A 0.75 mm2 / NO: 6 A, NC: 5 A 1 mm2 - 2.5 mm2 / NO: 9 A, NC: 5 A *This information alone may not be used to dimension the cables. To do this, other conditions such as cable type, type of installation, cable routing, cable length, etc. must be taken into account. Mandatory information:WEEE Reg. No.: DE34359026 Warnings: This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III). Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be avoided by carefully designing the light chain or lighting system and, if necessary, integrating the safety elements both in normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We will be responsible for any damage to property or personal injury caused by improper use or non-observance of the hazard warnings no liability. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Protect this product from electrostatic discharge to avoid damage. Any use other than that described in this usage information is not intended and will lead to warranty and Disclaimer.

(Shipping only to: DE, PL) Description This product is designed for use in conjunction with WLED controllers V31 / V41 / V62 / V63. It is helpful if you want to implement power distribution to several LED feed points. Variants with different fuses can be selected. Use WLED Power/Fuse/Injections Calculator to help you choose proper fuses.The fuse used in this product must have the nominal value less or equal to 10 A. Scope of delivery: Fuse board Accessories Matching housing is available separately Suitable fuses are available separately Technical data Operating voltage: 5..24 V Ambient temperature operation: +5°C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight without/with fuses: 20 g / 22 g Maximum permanent current carrying capacity per power path: up to 9 A (depending on cable cross section and environment) Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A (15 W) 0.75 mm2 / 6 A (30 W) 1 mm2 - 2.5 mm2 / 9 A (45 W) *This information alone may not be used to dimension the cables used. This requires other conditions, such as cable type, installation type, cable routing, cable length etc. be taken into account. WEEE Reg. No.: DE34359026 Danger information This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III). Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can destroy this Product and/or lead to a fire and must be ensured by a targeted design of the light chain or lighting system and, if necessary, by integration the safety elements can be avoided both during normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We will be responsible for any damage to property or personal injury caused by improper use or non-observance of the hazard warnings no liability. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Any use other than that described in this usage information is not intended and will lead to to exclusion of warranty and liability.

(Shipping only to: DE, PL) Description: This product is designed for use in conjunction with WLED controllers V43 / V63 / V70. It allows the 12V LED strips to be switched off in the “off” state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled. Usage information: HERE Scope of delivery: Relay board Accessories: Suitable housing is available separately Technical data: Supply voltage: 12 V +/- 0.5 V Ambient temperature operation: +5 °C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight: 45 g Maximum permanent current carrying capacity per power path (+12 V, GND): up to 9 A (depending on cable cross section and environment) Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A (36 W) 0.75 mm2 / NO: 6 A (72 W), NC: 5 A (60 W) 1 mm2 - 2.5 mm2 / NO: 9 A (108 W), NC: 5 A (60 W) *This information alone may not be used to dimension the cables. This requires other conditions, such as cable type, installation type, cable routing, cable length etc. are taken into account. WEEE Reg. No.: DE34359026 Hazard notes:This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III).Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be avoided by carefully designing the light chain or lighting system and, if necessary, integrating the safety elements both in normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We assume no liability for property damage or personal injury caused by improper use or failure to observe the hazard warnings. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Protect this product from electrostatic discharge to avoid damage. Any use other than that described in this usage information is not intended and leads to exclusion of warranty and liability.

(Shipping only to: DE, PL) Description This product is designed for use in conjunction with WLED controllers V31 / V41 / V43 / V63 / V70. It allows the 5V LED strips to be switched off in the "off" state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled. Usage information: HERE Scope of delivery Relay board Accessories Matching housing is available separately Technical data Supply voltage: 5 V +/- 0.1 V Ambient temperature operation: +5°C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight: 45 g Maximum permanent current carrying capacity per power path (+5V, GND): up to 9 A (depending on cable cross-section and environment)Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / Maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A (15 W) 0.75 mm2 / NO: 6 A (30 W), NC: 5 A (25 W) 1 mm2 - 2.5 mm2 / NO: 9 A (45 W), NC: 5 A (25 W) *This information alone may not be used to dimension the cables used. This requires other conditions, such as cable type, installation type, cable routing, cable length etc. be taken into account. Mandatory information:WEEE Reg. No.: DE34359026 Hazard notes This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the string of lights or lighting system to be set up (including e.g. Selection of the power supply, the light chain, cable selection, any necessary fuse elements) and using relevant to establish electrical engineering standards. Incorrect or improper use can be dangerous. Please read this completely Operating instructions before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III). Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be ensured by a targeted design of the light chain or lighting system and, if necessary, by integration the safety elements can be avoided both during normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We will be responsible for any damage to property or personal injury caused by improper use or non-observance of the hazard warnings no liability. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Protect this product from electrostatic discharge to avoid damage. Any use other than that described in this usage information is not intended and will lead to warranty and Disclaimer.