ABC! WLED shield for 5V and 12V LED (universal, V63)

Description: Plastic housing suitable for WLED boards: WLED V31 Board; WLED V41 Board; WLED V43 Board (5-24V); WLED V63 5V/12V shield with ESP8266 or ESP32; Relay board (5V, 12V or 24V); Fuse board Scope of delivery: Top part Bottom part 4 screws Mandatory information:Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München, Germany Warnings: This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. This product is only suitable for use in residential-like environments. Protect this product from direct sunlight. When used with the WLED Controller V43 together with the Ethernet adapter, an extra cutout must be made in the housing by the customer. Please see the product images for the Ethernet adapter.

(Shipping only to: DE, PL) Description This product is designed for use in conjunction with WLED Controller V43. It allows the 24V LED strips to be switched off in the “off” state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled. Usage information: HERE Scope of delivery: Relay board Accessories: Suitable housing is available separately Technical data Supply voltage: 24 V +/- 0.5 V Ambient temperature operation: +5°C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight: 45 g Maximum permanent current carrying capacity per power path (+24V, GND): up to 9 A (depending on cable cross section and environment) Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A 0.75 mm2 / NO: 6 A, NC: 5 A 1 mm2 - 2.5 mm2 / NO: 9 A, NC: 5 A *This information alone may not be used to dimension the cables. To do this, other conditions such as cable type, type of installation, cable routing, cable length, etc. must be taken into account. Mandatory information:WEEE Reg. No.: DE34359026Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München Warnings: This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III). Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be avoided by carefully designing the light chain or lighting system and, if necessary, integrating the safety elements both in normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We will be responsible for any damage to property or personal injury caused by improper use or non-observance of the hazard warnings no liability. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Protect this product from electrostatic discharge to avoid damage. Any use other than that described in this usage information is not intended and will lead to warranty and Disclaimer.

(Shipping only to: DE, PL) Description: This product is designed for use in conjunction with WLED controllers V43 / V63 / V70. It allows the 12V LED strips to be switched off in the “off” state using a relay. This saves energy, increases the lifespan of LED strips and provides additional security. Two paths enable two separate controls or, for example, two feeders to be controlled. Usage information: HERE Scope of delivery: Relay board Accessories: Suitable housing is available separately Technical data: Supply voltage: 12 V +/- 0.5 V Ambient temperature operation: +5 °C … +35 °C Ambient temperature storage/transport: -20 °C … 60 °C Dimensions: 78x47x20 mm Weight: 45 g Maximum permanent current carrying capacity per power path (+12 V, GND): up to 9 A (depending on cable cross section and environment) Screw terminals: Target torque: 0.4 Nm Screw terminals, cable cross section: 0.5 ... 2.5 mm2, rigid or flexible with wire end sleeve Screw terminals, stripping/sleeve length: 6-7 mm / 8 mm Cable cross section / maximum permanent current carrying capacity (maximum output power)(*) per path: 0.5 mm2 / 3 A (36 W) 0.75 mm2 / NO: 6 A (72 W), NC: 5 A (60 W) 1 mm2 - 2.5 mm2 / NO: 9 A (108 W), NC: 5 A (60 W) *This information alone may not be used to dimension the cables. This requires other conditions, such as cable type, installation type, cable routing, cable length etc. are taken into account. Mandatory information:WEEE Reg. No.: DE34359026Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München Warnings:This product is intended for use by persons with relevant electrical engineering knowledge and experience. This means that the person must be able to correctly dimension the light chain or lighting system to be set up (including, for example, selection of the power supply, the light chain, cable selection, any necessary safety elements) and to set it up using relevant electrical engineering standards. Incorrect or improper use can be dangerous. Please read these operating instructions completely before setting up your fairy lights or lighting system. This product may only be operated with safety extra-low voltage (SELF) (protection class III).Maximum permissible nominal value of the fuse is 10 A! This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. When connecting to the device terminals, please note the permitted cables and cross sections. Please note the technical data, especially the maximum current carrying capacity of the power path. Overloading can lead to the destruction of this product and/or a fire and must be avoided by carefully designing the light chain or lighting system and, if necessary, integrating the safety elements both in normal operation and in the event of a fault. Install and connect this product only when there is no voltage! Make sure the polarity is correct! We assume no liability for property damage or personal injury caused by improper use or failure to observe the hazard warnings. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Keep the usage information digitally or printed so that you can always access it. This product is only suitable for use in devices for apartment-like surroundings. Protect this product from electrostatic discharge to avoid damage. Any use other than that described in this usage information is not intended and leads to exclusion of warranty and liability.

(Shipping only to: DE, PL) Description: for V41 (5V), V43 (5-24V) and V70 Mini (5..12V) controllers also for universal 5V/12V shield (V63, with ESP32 and WLED SR version >= 0.13.3.7) Extends the controller with an analogue audio input for Sound Reactive WLED Special audio analog-to-digital converter (ADC) ensures that the analog audio signal is converted into a digital I2S signal, which can then be processed by the WLED controllerNew version V2: switch for normal/higher sensitivity Mandatory information: WEEE Reg. No.: DE34359026Manufacturer: MyHome-Control von Dr.-Ing. Wladislaw Waag, Wasserburger Landstr. 29, 81825 München Warnings: This product is intended for use by persons with relevant electrical engineering knowledge and experience. This product is not a toy! It must be kept out of the reach of children and must not be used as a toy. Install and connect this product only when the power is off! We assume no liability for property damage or personal injury caused by improper use or failure to observe the hazard warnings. In these cases, the warranty claim also expires! We assume no liability for consequential damage. Protect this product from electrostatic discharge to avoid damage.